BATCH VEGETABLE PEELER, Flott ZS-25, Y4149
Used Flott onion peeler, garlic peeler, potato, carrot, and batch vegetable peeler, Model ZS25, Alard item Y4149
Flott onion, garlic, potato, carrot, and vegetable peeler, Model ZS25 BATCH PEELER...
An abrasive batch peeling machine manufacturer recommended for garlic, onion, potatoes, carrots, beets, and other root crop vegetables with up to 1,760 pounds per hour capacity. Peeling action takes place at the bottom and sides of the machine which offers delicate peeling action, low noise cycles and reduced water consumption...
~ Load capacities per manufacturer literature:
+ Root Crops (potatoes, carrots, beets, etc): up to: 66 lbs (33 kg) per batch with an hourly throughput of 1,760 lbs (800 kg).
+ Onions: 55 lbs (20 kg) per batch with an hourly throughput of 1,320 lbs (600 kg).
+ Garlic: 44 lbs(20 kg) per batch with an hourly throughput of 1,100 lbs (500kg).
~ Peeling chamber measures 21.5 inch diameter by 14.5 inch deep with abrasive side panel and rotating abrasive bottom disk.
~ Side panel and bottom disk inserts can be changed depending on the product and type peeling desired.
~ 47 inch infeed height.
~ Water spray system assists with washing and removing peels.
~ Finished product is discharged thru a 10 inch diameter door with chute. Peels, debris & water have their own separate side discharge.
~ Hinged top cover with clear plexiglass center and safety interlock switch.
~ Equipped with start/stop controls and 6 minute timer.
~ 230 volt 3 phase electrical input.
~ Comes with three (3) interchangeable abrasive side panel peeling inserts and one (1) smooth insert designed for gentle washing.
As of this writing, this peeler is in stock at ALARD, in EXCELLENT operational, mechanical, electrical and cosmetic condition, ready to go and available for immediate shipment.
CALL 315-589-4511 to confirm availability and discuss your food processing needs.
ALARD item reference #: Y4149
CMI vegetable DIP TANK, WASHER, RINSER Y4896
CMI DIP TANK, WASHER, RINSER, fruit and vegetable preservative solution application tank, food grade, stainless steel. Complete with stainless steel recirculation pump, full length cleated elevating discharge conveyor with drive. Pneumatic power assist conveyor lift-out for sanitation / cleaning.
As of this writing, this fruit and vegetable dip tank washer is in stock at Alard Equipment in very good operational condition, available for immediate shipment.
CALL 315-589-4511 to confirm availability, and to discuss your particular food equipment needs.
Alard item Ref.#Y4896
Urschel M6 DICER, dicing HAM, Alard item Y4639
Urschel Model M6 DICER cutting ham, dicing ham...
URSCHEL MODEL M6 DICER...
A two-dimensional vegetable and meat cutter designed for dicing, strip cutting, or shredding a variety of products through a wide range of sizes. This versatile dicing machine, strip-cutter, and shredder is ideally suited for cutting beef, pork, poultry or fish through a wide temperature range from fresh chilled to hot cooked. Also manufacturer recommended as a leafy greens chopper for collard greens, kale, leeks, mustard greens, and spinach. This versatile machine is also recommended for cutting other food products into strips or squares including fruit leathers, flat breads, tortillas, pita chips, brownies, and croutons. This is a high-volume cutting machine that operates continuously at high production capacities, and is designed for easy cleanup and maintenance.
~ Infeed thickness of up to 1 inch (25.4mm).
~ Circular knife cuts from 3/16 to 1.5 inches (4.8mm to 38mm).
~ Crosscut knife cuts from 1/8 inch to 3 inches (3.2mm to 76.2mm).
~ STRIP CUTS can be made by removing the crosscut knife spindle. The length and thickness of the strips will depend on the size of the original product.
~ SHREDS - many types available for applications such as cooked pork, cooked beef, or cooked chicken, in medium, long or fine shreds.
~ This machine comes with 1/4 inch feed drum, and a 3/4 inch crosscut spindle. Circular knife spindle spacings can be easily adjusted in increments 1/4”. Other cutting parts are available from the manufacturer: --CALL 315-589-4511 to discusss your particular cutting specifications.
~ 10 inch wide feed belt with 35 inch length of open belt-feed area..
~ Includes factory stainless steel operator control panel with safety interlock system.
~ USDA food grade construction, including stainless steel cutting spindles, tubular support frame, guards, shrouds, infeed hopper and discharge chute.
~ 5 HP 208 / 230 / 460 volt 3 phase drive motor.
As of this writing, this Urschel M6 DICER is available in stock at Alard, in EXCELLENT operational, mechanical, electrical, and cosmetic condition, available for timely shipment.
CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food processing cutting equipment needs.
Alard item reference #:Y4639
NBE BIN DUMPER, Alard item Y4828
NBE BIN DUMPER, Alard item Y4828
A used National Bulk Equipment hydraulic bin dumper / tote dumper for 40 by 40 or 48 by 38 bins, totes, gaylords, boxes,toters, crates, etc. Stainless steel bin holder. Complete with onboard hydraulic pack. As of this video, this crate dumper is in stock at Alard Equipment Corp in EXCELLENT operational, mechanical, electrical, and cosmetic condition, available for immediate shipment.
CALL 315-589-4511 to confirm availability, and to discuss your particular bulk food product handling equipment needs.
Alard item reference #: Y4828
Alard Turbulent Flow Jet Washer Y4262
Alard TURBULENT FLOW JET WASHER, leafy green, fruit and vegetable WASHER FLUME, food grade stainless steel...
An AGITATED IMMERSION WASH SYSTEM, wash and chill flume, with water-jet agitation for gentle but active washing for pre-cut fruits and vegetables, including cut or whole leafy greens, including delicate leaf products like spinach, baby spinach, spring mix and other pre-cut produce food products.
~ This spiral-flow WASH FLUME is 11 feet long by 31 inches wide with agitating water jets all along the left-side near the bottom to provide spiral water flow for gentle immersion washing of delicate food products.
~ The wash tank overflows onto a 5 foot long by 30 inch wide ELEVATING DISCHARGE CONVEYOR with an interlocking chain type belt with fine perforations to allow the water to pass through while discharging the dewatered product onward.
~ The conveyor is powered by a .5 HP stainless steel shrounded motor with an aluminum shrouded gear reducer.
~ The water falls through into a stainless steel catch and balance tank, with a new Thomsen model 8 stainless steel RECIRCULATION PUMP with 7.5 HP motor.
~ Check valve included to keep the wash tank water from draining into the wash tank when the pump is shut off.
~ All pipe fittings / connections are USDA food-grade sanitary.
~ All food-grade sanitary stainless steel construction.
~ The water jet nozzles are removable for sanitation.
~ All drives 208/230/460 volt 3 phase electrical input.
As of this writing, this spiral-flow washer is NEW IN STOCK at Alard, in fully assembled and available for immediate shipment.
CALL 315-589-4511 to confirm availability, and to discuss your fresh-cut produce packing and process equipment needs.
Alard item reference #: Y4262
Food METAL DETECTOR with conveyor belt, 20x8, Cassel Metalshark, Y4768
FOOD PROCESS METAL DETECTOR with BELT CONVEYOR, 21x8, 304 stainless steel...
A Cassel Metalshark2 MULTI-FREQUENCY washdown sealed 304 stainless steel conveyorized metal detection system for industrial process applications, with...
~ Approximately 8 inch (203mm) high by 20.6 inch (525mm) wide net USABLE aperture opening with the conveyor belt in place.
~ The 304 stainless steel frame washdown belt transfer conveyor has a 70.5 inch (1791mm) long by 18.5 inch (470mm) wide interlocking plastic chain type belt, running at a 31.5 inch (800mm) working height, with adjustable feet allowing +/-4 inch (100mm) height adjustment.
~ The thru-conveyor is complete with a photo-eye product sensor, a belt-stop alarm reject configuration, and a variable speed control for the 110 volt single phase drive, adjust able from 16 to 75 feet per minute (approximately 5 to 23 meters per minute) belt speed.
~ A food grade metal detector specifically built for food processing and other industrial production line metal detection applications. All food grade / USDA sanitary hose-wash-down stainless steel construction (IP-67/NEMA 6 search head enclosure, IP-65/Nema4,4x,6,12 & 13 control enclosure).
~ The search head is complete with integral touchpad operator controls with a 5.4 inch color screen, including RS-232 and RS-485 serial data acquisition ports, and ethernet data interface, in a stainless steel enclosure. Optional data logging software is available for tracking and reporting for HACCP and other quality assurance and certification regimes.
~ 110 volt single phase (standard household current) electrical input.
~ FOUR FREQUENCY LEVELS (35kHz, 75kHz, 150kHz, and 300kHz), allowing for optimal
sensitivity across an exceptionally wide range of products / product types (wet, dry, salty, meat, fruits, vegetables, fresh, frozen, hot, cold, etc) allowing for maximum versatility with the widest range of products. The optimal frequency is automatically set by the system in "product learn" mode to maximize sensitivity / minimize false rejects with your specific product.
~ Sensitivity varies depending on product run, and frequency setting (determined by product characteristics), especially where wet, salty, or acidic products that are electrically conductive introduce "product effect" into the equation.
~ Quick teach feature learns new products in 4 to 7 passes.
~ The control unit allows for 120 product presets, where product presets save the frequency setting with the other tuning data.
~ Single control board technology with all control electronics on one circuit board maximizes reliability, and minimizes maintenance expenses.
~ 304 stainless steel search head and conveyor construction.
~ NEW EQUIPMENT - Includes a 2 year manufacturer warranty on hardware / parts.
As of this writing, this conveyorized metal detection system is in stock NEW at Alard, ready to go and available for immediate shipment.
CALL 315-589-4511 to confirm availability, and to discuss your particular industrial product inspection needs.
Alard item reference #:Y4768